Видео

As Popeye says, "Well blow me down."

You said the lines were cold at the start when it was broken, but then at then end when you fixed it the lines are still cold?

That older one probably stronger lol

Mittens on a long string is cheaper. 😂😂😂

Anyone ever heard of a pocket

What size is the inner rubber tube? I see the fitting is 3/4 inch, but i dont the measure for the inner hose. Thanks

You do know there are rotary tools with little blades that will cut that

Can I have your cord😅

You need a huge backpack blower so you can blast wet leaves piled as high as you. 😅

Wow nice blower Brian thanks for the info 👍

The front is damaged

Where do I check what capacitor I will need for mine ?

That magnet add-on... you'd have to be super accurate with the correct amount of force. otherwise, your wood will look like a target sheet for guns. And listen to his clean speech while using the regular hammer, and then the shocker skips his arm and makes his voice quiver, so imagine your shoulder and neck eating the recoil from shock hammering all day. Meh its cool enough for me to say nothing by saying alot, too much even.

How does it cope with UV rays though?

Its the Flux Capacitor!!!

That's a nice hose but "safe to drink" is not a thing. When you turn off the water, you usually have standing water in the hose. That's the main issue with hoses. Bacteria and mold live inside the hose.

😂 I remember when a hose was a hose and you just drank from it!

Somebody put some thought into this !🤙

Plastic end fittings won’t last for me.

Wow what a nice hose thanks for sharing Brian 👍

Out Friggin' Standing !!! 👍

Don't really need that angle stop tool. It's something else to carry around. I just snap my vice grips on the valve and turn the nut with my crescent wrench.

You'd be a great neighbor to have. Great job! 👍🏼

Just saved me a service call on a Sunday. Thank you!

Nicely done! Good to know about that tool!👍

This is what I hate about plumbing! The pipes coming out of the wall are always loose & moving around, but you have to use 2 tools in a tight space & pray you don't break or bend your pipes just trying to change that angle stop. All of mine need to be changed. I did one under the kitchen sink & bent the copper tubing. It took every bit of strength I had 😂 to get it loose & still had to call a plumber. I asked him what I did wrong, & he said I was too strong lolololol. I would rather shovel horse manure than do plumbing. Why anyone would make it this hard just stumps me, except to make money of course. And, I agree, your neighbor has a lot of problems with plumbing. Like me 😁

Hey Brian great video and information thanks take care and I hope you and your family have a great rest of your weekend 👍

Your video is good overall, but I really think you should cover the problem of getting the ferrule off and properly tightening the new valve. The ferrule can be really tough to get off, even with a puller. I once mushroomed the end of the pipe trying to get the ferrule off with a puller. For that reason, I like the small hacksaw cut method. If you have a lot of ferrules to get off then, the puller is probably the way to go. The other thing is how to tighten the valve nut and new ferrule after prep. I did what I thought was correct according to the manufacturer's instructions. Didn't want to tighten it too tight, but then again not enough. I went with a half turn or so by marking the nut with a sharpie. I was so concerned that it might pop off and flood my home that I called my favorite plumber to verify that I installed it right. He said that I did it the way he would have done it. Maybe I'm overthinking this, but when you've gone through water damage in your home that cost around $10K to fix, you want absolute confidence. I did a second one, but had to tighten it about 3/4 turn to get it to stop leaking. Anyway, I could probably write a book on these compression angle stop valves.

Wow, "your neighbor" has ALOT of plumbing problems!...

Do you happen to have any information on that collet puller where to buy one? It looks like it pulls the collet off easier that some off the other pullers.

Thanks brother!!

is there a way to disable these? I don't want air sucking into the hose every time - plays heck with my pressure washer

Thanks guy, from South Carolina!

More escutcheon for the pushin

Awesome informative video brother. I am sure this one will be a big help for some people. Hope you and the family are doing great and as always it is great to see another great video.

Wow I have a wobbly toilet in my upstairs toilet.

7:08

Amazing!!! Thanks for sharing!!! SUB and LIKED!!!

75 psi you need a pressure reducing valve

7:01

Great info but I call it "Phishing" title. The are multiple videos on same issue. If they are all titled similar way as yours you have to watch all of them to find out that they are about same issue. There fore getting HVAC guy would be cheaper than spending more than hour watching youtube on same issue. You have good content in this video don't ruin it with tricky title. Simply bad capacitor in brackets would solve it.

very helpful having the same problem thanks man!

I wanted to see wheels on the tall one so you could use it like a dolly, just tip it back and wheel it

The flange should be flush with the floor, the last spacer was 100% not necessary

What is the name of the auger.?

Teflon on the threads, silicone under the basin lip. That’s it. Nothing additional needed underneath if compressed correctly.

Clean you toilet of put a new wax ring on it. Shouldn’t smell

He officially has two fart boxes